VX-3308WM

New Compact Voice Alarm System

The VX-3308WM is a combined PA and VA system based on the VX-3000 system and is certified according to the European Standard EN54-16. It is designed to be wall-mounted requiring little space and can be operated as a stand-alone unit as well as being combined with all VX-3000 units. Due to the scalable and integrated architecture of the VX-3000 system, the VX-3308WM is an ideal solution for distributed locations, for example, to cover the many floors of a high-rise building.

It provides 8 speaker line outputs/zones that can be switched between two amplifiers. This allows broadcasting two different audio signals simultaneously on the same speaker lines. The amplifier modules can be easily mounted and removed. Up to 3 power amplifier modules of different wattages can be mounted, two of which drive the speaker lines and one is a standby amplifier. Each amplifier channel has the following DSP functions: different filter types (PEQ, HPF, LPF, shelving, CD-horn EQ, notch), compressor and delay that enables appropriate acoustic adjustment for any broadcast area. The smart ANC function enables the control of ambient noise and is not affected by the audio signal it controls. Therefore, the sensor’s installation location is not critical. The monitoring of the speaker lines can be selected between impedance monitoring with selectable pilot tone or by end-of-line modules.

The VX-3308WM has 4 balanced audio inputs with selectable sensitivity from microphone up to line level, with phantom power selection for microphone use. The inputs can also be set for receiving an emergency broadcast from another VA system of higher priority and broadcast it under the condition of the emergency mode. Up to 8 remote microphones can be connected via RJ45 ports; two of which can be emergency microphones. The following DSP functions are available for each input channel: different filter types (PEQ, HPF, LPF, shelving) and a compressor. Helpful features such as feedback suppressor or voice-controlled broadcast activation (VOX) enhance the usability of the system.

  • Complete PA and VA system in one unit, including power supply and power amplifiers
  • Compact, flat unit that can be mounted in narrow environment (e.g. corridor)
  • Cost and time effective: all components and two 300 Watt amplifier modules pre-assembled and connected
  • One optional amp can be added
  • All indications and controls according to EN 54-16
  • Fault status indication for each speaker line
  • Operation and audio signal status indication per amplifier
  • 8 control outputs by open-collector-transistor and 4 by 5 A relays
  • 16 standard and 2 voltage-controlled control inputs with monitoring
  • IP network-based, max 160 units can be combined
  • Fully compatible with the (rack-mounted) VX-3000 system




  • Spezifikation
  • Einsatzbereiche
  • Zubehör
  • Ausschreibung
  • Downloads
Spezifikation
Spezifikationen zum Produkt:
VX-3308WM
Power source

220 - 230 V AC, 50 / 60 Hz (AC-mains)

Frequency response

40 Hz - 20 kHz (±1 dB)

Distortion

< 1 % (at 1 kHz)

Power consumption

1100 watts (at rated output incl. charging), 460 watts (EN 60065)

S/N ratio

60 dB (A) (or more, at DA control link)

Control input

16 (contact), 2 (voltage controlled), all with surveillance

Control output

8 (open collector, no-voltage make contact, control current max. 10 mA, withstand voltage 28 V DC, on RJ45 jack).

4 (no-voltage make contact, relay contact (NC, NO, C), control current: 2 mA to 5 A, withstand voltage: 125 V AC, 40 V DC, Connector: removable terminal block (12 pins)

Input / Output

4 balanced audio inputs, sensitivity -20 dBV (line)/-60 dBV (mic), impedance: 47 kohms, phantom power 24 V selectable by software.

2 remote microphone inputs for up to 8 units.

8 speaker line outputs, insulated from earth

Indicator

AC Power in (green) ×1, Run (green) ×1, Emergency (red) ×1, CPU Off (red) ×1, LAN A (green) ×1, LAN B (green) ×1, RS Link A (green) ×1, RS Link B (green) ×1.

Fault Status (yellow): General ×1, Unit ×1, Network ×1, EMG Mic ×1, Fuse ×1, Power ×1, CPU ×1, Zone ×8.

Amplifier: Peak (red) ×3, Signal (green) ×3, Operate (green) ×3, Power (green) ×3.

Battery (green): Charging ×1, Battery power ×1, connection ×1, condition ×1

Connection

AC-mains: 2 pin screw terminal at breaker, 1 screw terminal for earth

Speaker outputs: 6-pin removable screw terminal block ×4

Control inputs: 9-pin removable screw terminal blocks ×3

Emergency control inputs: 5-pin removable screw terminal block ×1

Control outputs: 9-pin removable screw terminal block ×1, 12-pin removable screw terminal block ×1

Network: 9-pin removable screw terminal block ×2

Internal connections:

DC power supply (max. 25 A): 2-pin screw terminal ×1

DC power supply 24 V DC, 0.3 A: 4-pin removable screw terminal block ×1

Operating humidity

90% RH or less (no condensation)

Operating temperature

-5 °C to +45 °C (23 F to 113° F)

Finish

Steel plate, surface-treated, 30% gloss, black (RAL 9011 or equivalent)

Weight

33.1 kg

Accessory (included)

Removable terminal plugs: 9 pins ×8, 6 pins, 3.81mm ×2, 5 pins ×1, 6 pins, 5.0mm ×4, 12 pins ×1, 4 pins, 3.81mm ×1, CD (PC setting software) ×1, Battery cable 80 mm ×1, PA connecting cable 16pin ×1, PA output cable 2pin ×1, DC Fuse 30A ×1, 1 m double Velcro tape ×2, battery pole cover ×4, Key ×2

Einsatzbereiche
Zubehör
Ausschreibung
Downloads